The Best Recessed Dryer Vent Box

Why The Need For The Dryer Box? In the past, homeowners had to put up with the inefficient venting of their dryer appliance exhaust due to numerous friction causing bends or kinks in the flex duct hose that connects the dryer to the wall exhaust pipe. Lint build up and a fire hazard are the unwelcome bi products of these annoying bends. In order to accommodate these flow restrictive bends, the dryer appliance had to be located five to six inches away from the wall, taking away from valuable living area. The Dryer Box solves these issues and provides much more in benefits to the builder, the contractor and the homeowner. What Are The Benefits Of The Dryer Box? Locate the dryer right up against the wall Flex is protected from getting squished No trim ring piece is needed Lint build up is minimized Efficiency is increased Dryer related service calls are almost eliminated Elbow eliminator gain 5 foot of duct run Doubles as gas connection receptacle Can be installed in One Hour wall Meets code requirements as a clean out Laundry room appears larger to prospects Surface is paintable, no masking needed Applauded by building inspectors Reduces the fire hazard Socks and clothing can t fall behind appliance Prevents costly punch out work to damaged 90 Eliminates mold potential Contributes 2 USGBC LEED credits Which Are The Specifications For The Dryer Box Model 425? Designed for upward exhaust direction 22 gauge aluminized steel weighing 4.14 pounds each Top port measures 4 1/8 with very slight oval shape Distance from nailing flange to rear of box is 4 1/4 Overall measurements: 21 h x 12 1/2 w x 5 1/8 deep Inside measures 9 1/2 wide x 18 1/4 tall.

The Saf-T-Duct Dryer Outlet Box from Builder’s Best finishes off dryer vent rough-ins and easily adds or recaptures space in the wall behind your dryer for venting. The unit can be used in-wall (prior to drywall) or on-wall (after drywall is installed). The standard 4 in. round connections allow for the best airflow and connect easier than ovals.

Dryer Dock Dryer Vent 6″ for 4″ Tubes, White

This indoor dryer vent is designed to capture the lint from your electric clothes dryer, for those unable to vent to the outside. All types of indoor dryer vents will allow heat and humidity into the room. We recommend the user allow for air circulation and ventilation when operated in confined spaces. This patented double filter system does not use water, eliminating messy cleanups. The stainless steel screen acts as a pre-filter capturing large lint particles, pet hair, etc. and can be cleaned with a sweeping motion of the hand. The polyester filter will capture the finer lint dust and can be vacuumed clean for extended use or replaced when fully loaded with lint. Replacement filters are available in packages of 6, lasting most users up to a year under normal conditions. There is a patent pending “safety vent flap” designed to open, as a reminder to clean the screen and filter. For renters or homeowners concerned with dryer lines that exceed the dryer manufacturer’s recommendations, resulting in inefficient operation and lint accumulation, this is a great solution. Saves energy in colder months by returning warm dryer air into the room. All installation hardware included. Customer supplies hose and clamps. Installation is quick and easy, instructions included. If you’ve purchased this product in the last 30 days and one or both of the side clips is broken, please reach out to [email protected] for a replacement.

The MV-90 is designed for when the vent path takes a 90 degree turn, such as down through the floor, up through the ceiling, or off to the side. -The MV-90 can handle offsets up to 3 inches from center to center. The more accurately you line up the MV-90 with the vent on the back of your dryer, the better the vent path and the further back you can locate your dryer. Normally, the MV-90 requires 5 1/2 inches of clearance behind the dryer. If an obstruction necessitates you locate the MV-90 at the maximum 3 inch offset, then your dryer will need to sit out an additional 3 inches to allow for a bend radius in the transition duct. -Close vent offsets between dryer and wall vent located on same wall as dryer (Offsets between 6-9 inches): The MV-90 can be coupled directly to a standard 4 inch diameter, adjustable, 90 degree elbow which creates a 9 inch offset. See photo below. If your same wall offset is 6 inches, you can use the MV-90 and an elbow, taking advantage of its ability to handle misalignment up to 3 inches. -Same wall offsets greater than 9 inches: Simply mount the MV-90 directly behind your dryer, plug the 90 degree elbow into the wall vent, and measure for the required length of rigid metal pipe between them. Make sure to measure from where the pipe will stop on the MV-90 to the stop on the male end of the rigid metal pipe. -Close vent offsets between dryer and wall vent located on same wall as dryer (Offsets between 0-3 inches): If your same wall offset is between 0 and 3 inches, then the MV-180 is the product for you.

The EZ Dryer Vent is a White metal box that attaches to the wall or floor on the back of a dryer, it connects to a magnetic boot on the dryer for easy connecting and disconnecting from the dryer vent. This gives you easy access to the back of your dryer to clean the ducts and retrieve lost items without crimping the duct each time. The EZ Dryer Vent comes with soft pads so the dryer moves easily. The EZ Dryer Vent is 10 inch x 10 inch x 4 inch and fits on most dryers and is easy to install.

Product Description

This Dura Safe Close Elbow effectively turns 90 degrees within 4-1/2 Inch. It features snap-lock fittings and rotating collars. It is an ideal product for limited space installations.

From the Manufacturer

This DuraSafe Close Elbow effectively turns 90 degrees within 4-1/2 inches. It features snap-lock fittings and rotating collars. It is an ideal product for limited space installations.

Recessed dryer box, the dryer can now be pushed up against the wall of the laundry room instead of having to be positioned 5″ to 6″ away from the wall in order to accommodate the dryer duct. The duct will also be completely protected from crushing and lint build-up will of course be minimized due to the limited bends. Dryer box also has the additional features of a built-in draft blocker to help reduce cold air backdraft into the home as well as an oval to round duct adapter which requires no clamps to connect to the duct and eases installation. Home owners will benefit from the dryer’s efficiency and the contractor will receive less call backs. Face plate dimensions: 12.05″ W. x 17.5″ L. x 3.45″ D. Color: White.

Dvbox 17.38×11.5×4.5 Dryer Venting Box