Top 9 Dryer Vent Hose For Small Space

This 010149 Zero Periscope is specifically designed for use in situations where the dryer Outlet overlaps or is very close to the wall Outlet. The 2 inch by 6 inch smooth aluminum construction telescopes to handle outlets up to 5 inches distance from center to center. The 4 inch diameter draw band collar synchs down over the clothes dryer vent i.e.. The 4 inch diameter crimped fitting slides into most wall ies. Once installed, it needs only 2.5 inches clearance behind the dryer. If your outlets are very close and you need to move the dryer closer to the wall, this vent maintains critical airflow and provides all metal performance. Clothes dryer manufacturers specify “only rigid or flexible metal vent shall be used for exhausting. Do not use plastic or metal foil vent.” installation instructions are included inside each carton. The zero periscope is built in the USA by Builder’s Best, Inc.

Product Description

This periscope can range from 0 to 18 Inch depending on preference. It includes one male snap-lock fitting and one extra long draw-band collar. Keep in mind that any excess length can be trimmed to fit according to your needs.

From the Manufacturer

This periscope can range from 0 to 18 inches depending on preference. It includes one male snap-lock fitting and one extra long draw-band collar. Keep in mind that any excess length can be trimmed to fit according to your needs.

The MV-90 is designed for when the vent path takes a 90 degree turn, such as down through the floor, up through the ceiling, or off to the side. -The MV-90 can handle offsets up to 3 inches from center to center. The more accurately you line up the MV-90 with the vent on the back of your dryer, the better the vent path and the further back you can locate your dryer. Normally, the MV-90 requires 5 1/2 inches of clearance behind the dryer. If an obstruction necessitates you locate the MV-90 at the maximum 3 inch offset, then your dryer will need to sit out an additional 3 inches to allow for a bend radius in the transition duct. -Close vent offsets between dryer and wall vent located on same wall as dryer (Offsets between 6-9 inches): The MV-90 can be coupled directly to a standard 4 inch diameter, adjustable, 90 degree elbow which creates a 9 inch offset. See photo below. If your same wall offset is 6 inches, you can use the MV-90 and an elbow, taking advantage of its ability to handle misalignment up to 3 inches. -Same wall offsets greater than 9 inches: Simply mount the MV-90 directly behind your dryer, plug the 90 degree elbow into the wall vent, and measure for the required length of rigid metal pipe between them. Make sure to measure from where the pipe will stop on the MV-90 to the stop on the male end of the rigid metal pipe. -Close vent offsets between dryer and wall vent located on same wall as dryer (Offsets between 0-3 inches): If your same wall offset is between 0 and 3 inches, then the MV-180 is the product for you.

Dryer Dock Dryer Vent 6″ for 4″ Tubes, White

This dryer vent kit includes parts necessary to connect a dryer to the wall vent. This kit includes a flexible 8 ft. Pipe and a close elbow with two metal clamps. The air flow of this dryer vent kit allows for enhanced drying time of the connected dryer.

Product Description

This Dryer Telescoping Vent Periscope measures 18-in L to 29-in L and is designed for use in small laundry spaces with 2-1/2-in clearance. It features one male snap-lock fitting and one extra long draw-band collar for easy installation; excess length can be trimmed to fit. The beveled ends of the item prevent interference with or damage to floors and wall. This is an accessory that can be used across several brands; check to see if your model number is compatible. Installing this accessory will require basic hand tools and novice repair experience.

From the Manufacturer

This periscope can range from 18 to 29 inches depending on preference. It includes one male snap-lock fitting and one extra long draw-band collar. Keep in mind that any excess length can be trimmed to fit according to your needs.

Quick fit aluminum vent kit, used for clothes dryers, no clamps needed, easy to install, rubber gasket secures one elbow to the dryer exhaust outlet & the other elbow to the wall plate, includes: 4 inch x 8′ flexible aluminum duct, 2 elbows & 1 wall plate.