Top 9 Ao Smith Gcrl40 40 Gallon

The ProMax family offers a wide range of water heating solutions-from models that help you qualify for gas utility rebates to high recovery models ideal for large families with high demand for hot water. And, our specialty vent gas water heater options can be installed almost anywhere in your home because they can vent up to 40 feet. Our direct vent models feature two-pipe combustion systems that draw clean air from outside the home, eliminating any worries about indoor ventilation.

The ProMax family offers a wide range of water heating solutions-from models that help you qualify for gas utility rebates to high recovery models ideal for large families with high demand for hot water. And, our specialty vent gas water heater options can be installed almost anywhere in your home because they can vent up to 40 feet. Our direct vent models feature two-pipe combustion systems that draw clean air from outside the home, eliminating any worries about indoor ventilation.

279838 Heating Element is rated at 5400 Watts 240 Volts and has 2- 5/16″ male terminals.
279838 heating element replacement for numbers 2438, 279837, 279838, 279838A, 279838VP, 3398064, 3403585, 8565582, AP3094254, W10724237.

3977767 Dryer Thermostat is a hi-limit thermostat with Terminal Extension Arm.
It acts as as safety mechanism that keeps the dryer from overheating.
Once the dryer temperature reaches 221 degrees Farenheit, this piece will shut down power to the heating element until it drops by 80 degrees Farenheit
3977767 dryer thermostat replaces part numbers 3399693, WP3977767VP, AP3131941, 898078

3392519 dryer thermal fuse is used indryers as a safety mechanism that stops the flow of electricity to the motor circuit when a dryer overheats.
This replacement part features two 3/16 inch terminals, and is sold individually.
When this fuse is faulty, your dryer will not start or it will not heat properly.
This is a one-time fuse, meaning it cannot be re-set.
It must be replaced when there is no longer continuity between the terminals.
3392519 dryer thermal fuse replaces part number 3388651, 3392519, 694511, 80005, WP3392519VP

Works with most top name brands:  Whirlpool, Kenmore, Roper, Maytag, Estate, Inglis, KitchenAid, Crosley, Amana, Admiral, Magic Chef.

Package list:
1PC 279838 Dryer Heating Element
1PC 3977767 Dryer Thermostat
1PC 3392519 Dryer Thermal Fuse

Siwdoy Customer Service

Siwdoy is committed to providing each customer best customer service. if any question ,Please don’t hesitate to contact us.

Product Description

Factory pre-charge: 38 psi (pounds per square inch). maximum working pressure 100 psi. Maximum operating temperature 200 F (Degree Fahrenheit). engineered to provide years of trouble-free service using cold rolled steel for a higher strength to weight ratio. Rugged, stable steel base with protective plastic strip. Heavy-duty butyl rubber diaphragm and durable polyolefin liner to prevent corrosion. Water worker tanks feature an appliance quality finish which is resistant to sunlight and harsh conditions. All tanks are completely lead free for safety. Meets nsf (National Sanitation foundation) standard 61 for clean, safe drinking water. 5 year warranty. Blue tank.

From the Manufacturer

The WaterWorker pre-charged tanks utilize a butyl composite diaphragm, which flexes up and down based on water level and air pressure, as the pump fills the tank with water the air above the diaphragm is compressed, increasing the pressure in the tank until the pump cut-off pressure is reached. When water is drawn from the tank, the pressure inside the tank decreases until the pressure switch starts the pump. The amount of usable water for every pump cycles is called drawdown. The greater drawn-down capacity you select, the less your pump cycles saving energy, money, and extending your pump life. Advantages over galvanized well tanks: Pre-charged tanks do not have water-logging problems like the galvanized tanks. The air and water are totally separated using a diaphragm. No external air controls needed. Pre-charged tanks have a much larger draw-down for the same physical size. Larger draw down reduces pump cycles and pump wear, i.e. at 30/50 PSIG range three times the draw-down for pre-charged tanks of the same physical size. Pre-charged Tanks completely empty during each pump cycle. Pre-charged Tanks are much smaller and easier to handle that galvanized well tanks. Pre-charged tanks with a 30/50 Pressure Switch would be one-third the size of a galvanized tank with the same drawdown. Deep Well Jet Pumps could use either a vertical tank or a horizontal tank, depending on space requirements and sizing. Submersible Pump applications would usually use vertical tanks, again based on proper sizing. Shallow Well Jet Pumps could use vertical or horizontal tanks, based on proper sizing. The rule of thumb in sizing is to count the number of fixtures in the home, i.e. sinks, showers, toilets, dishwasher, faucets, washing machines, outside faucets, etc. and multiply it by 3. Example: a house with 11 fixtures x 3 would be 33-Gallon tank. We would suggest our 44-Gallon tank, which is the next larger sized tank.

Product Description

4500W/240V Screw-In Element 02343

From the Manufacturer

Camco’s 4500W 240V screw-in type high watt density water heater elements can be used in all screw-in replacement situations if the same wattage and voltage are used. High Watt Density water heater elements are the most common and the same type of element provided with most new water heaters. They are easy to install and come with detailed instructions on how to replace your old element. Screw-in type elements fit most models of American, AO Smith, Bradford White, Craftmaster (prior to 1991), GE, GS Wood (certain models), Kenmore, Lochinvar, Maytag, Mor-Flo, Reliance, Rheem, Richmond, Rudd, Sears, State, Whirlpool and most water heaters manufactured after 1994. The replacement element must be the same voltage and wattage as the element being replaced. Never exceed the nameplate rating on the water heater.

This lid is designed to use with Pentair SM & SMBW 4000 Series pool/spa D.E. filter model 4048. Measures 22-inch length by 20-inch height by 22-inch width.